Dimensions Guide

Cars and Vehicle

Knowing the trailer axle dimensions and how to measure them is necessary so you can get the appropriate one. Although there are different types of axles, the measuring process is essentially the same.

Required Tools and Materials

Lug wrench
Measuring tape
Helper

Step 1

Jack the trailer up and take off the tires.

Step 2

Ask your helper to hold the measuring tape to the hub front. This would be the area where the wheel is set against. Measure the distance from one hub face to the other. The figure you get is the track width.

Step 3

To get the other trailer axle dimensions, ask your assistant to put the measuring tape at the middle of one of the spring mounting pads. Look at the figure at the middle line of the other pad. This will be the spring distance. The spring distance and track width measurements are needed if you’re going to purchase new trailers.

Step 4

Take the measurement from the spindle center line to the middle line of the axle tube. This is how you get the axle drop. While you’re at it, check the position of the spring pad below or above the axle.

What to Look for When Buying Axles

Along with the trailer axle dimensions, you’ll also have to consider the following specs. The first is load capacity. The load rating needs to support the maximum gross vehicle weight rating (GVW).

If you have multiple axle trailers, divide the gross vehicle weight by the axles. The result is the load capacity (minimum) for every axle. The other vital specs are track length, the spring centers and overall length (from spindle to spindle).

Axle Types

These include straight axles, which can be square or round, torsion axles and drop axles with offset spindles.

Axle Specifications (Marshall Engineering)

The axle 39 mm round straight comes in six types: the 65" (4′ wide trailer) std offset, 67" (4′ wide trailer) deep offset, 71" (4′6" wide trailer), std offset, 73" (4′6" wide trailer) deep offset) and 7" (5′ wide trailer) std offset.

The 40 mm trailer axle dimensions and types include the following; 65" LM (4′ wide trailer) std offset), 67" LM (4′ wide trailer) deep offset, 71" LM (4′6" wide trailer) std offset, 73" LM (4′6" wide trailer) deep offset, 77" LM (5′ wide trailer) std offset and 82" LM (5′5"’ wide trailer) std offset.

45 mm Axles

The axle 45 mm specs are as follows: 65" (4′ wide trailer) std offset, 71" (4′6" wide trailer) std offset, 77" (5′ wide trailer) std offset, 82" (5′5" wide trailer) std offset, 89" (6′ wide trailer) std offset, 91" (6′ wide trailer) deep offset, 95" (6"6′ wide trailer) standard offset and 97" (6"6′ wide trailer) deep offset.

Lazy axles include 1.0T 40 mm square (Ford/Holden), 1.4T 45 mm square (Landcruiser), 2.0T 50 mm square (Landcruiser / 6 stud) and 3.0T 63 mms square (Landcruiser / 6 stud). The lazy axles are all ready to be fitted.

Again, these trailer axle dimensions are for Marshall Engineering only. Other axle manufacturers may have other sizes.

Riding a motorized bicycle can be a unique and thrilling experience. If you’re not familiar with their features, the descriptions of these models should help you develop a sense of what these bikes are like.

Dimensions of Motorized Bicycles: Venus

The Venus bike has a 50" wheelbase with cantilever frame. There are 26 x 2.125 black alloy wheels complete with 36 stainless spokes. The white wall tires measure 26”. The inner tubes measure 26” and are invulnerable to thorns.

The engine is 48cc or 66cc Skyhawk. The handlebars are chrome as is the 60mm reach neckstem. The front sidepull brakes have 70mm brake pads. There is a 1" threaded headset. There are rear and front reflectors, tooth engine drive chain sprocket and it has clean emission. The bicycle can go 75 mph with a half gallon tank.

Dimensions of Motorized Bicycles: Bare Bones

This is a cantilever framed cruiser that is equipped with stout tubing. The cruiser tread white wall tires are 26”, while the alloy wheels measure 26" x 2.125". The handlebar is chrome and it also has 36 – 14 gauge spokes and red rims.

The bicycle is equipped with 70mm brake pads. The inner tubes measure 26”. The bicycle also has rear and front reflectors. The seat is black. The PVC pedals are black and come with reflectors. The bike is sold in the following colors: matte grey, midnight blue, gloss black, red and matte black.

Dimensions of Motorized Bicycles: the Violation

The Violation has 4" x 4" cruiser pedals and 26” inner tubes. Like the other models, the brake pads are 70mm. There is 1 1/8" (28.6mm) grating chrome plated seat post, and colored rims. The tread tires are 26” Black Kenda Flame.

The headset is 1 1/8" (28.6mm) NESCO (water resistant). The side stand is black, and the seat has white and black piping spring. The bike is good for 150 miles on a full tank. The bike has 2 cycle engines, so the lubrication is in the premixed gas.

Dimensions of Motorized Bicycles: Hot-Shoe Racer

The Hot-Shoe Racer has 26 x 2.125 wheels with 36 spokes. The inner tubes measure 26”. Other features include 3-piece hot forged aluminum crank arm set and 1" threaded headset. There is a race handlebar with vintage styling and 26” black race tire.

The rear stand is black steel. The brakes are front linear pull V-brake and rear coaster. The engine can be 66cc or 48cc Skyhawk. The engine is good for up to 10,000 miles. The setup is similar to a motorcycle.

The clutch is situated to the left and the front brake and throttle are to the right. The bicycle has a choke for cold starts. It is possible to pedal without utilizing the engine at all.

The dimensions of motorized bicycles are somewhat similar, but some elements are unique for each model. Whichever bike you get, make sure to follow all the instructions for driving it. You should also obey the guidelines on how to properly take care of it.

The bumper is one of the most important parts of a car, which can be found at the rear-most and front-most parts. It helps the vehicle sustain tremendous impact while preventing the safety systems from being damaged. However, it can reduce the injury of passengers especially during high-speed impacts. It can somehow lessen the injury that pedestrians can suffer after being hit by a car. In addition to these facts, it is also interesting to find out the car bumper dimensions.

Dimensions of a Car Bumper

In terms of height, the bumper of a passenger car must not go beyond the range of 41 to 51 centimeters or 16 to 20 inches. This standard rule applies to all cars although the actual sizes of their bumpers vary. The use of bumpers in a car is a legal requirement in most jurisdictions. It is important to abide by this rule so as not to cause bad outcomes in case accidents happen.

Additional Facts and Other Interesting Details

The United States National Highway Traffic Safety Administration (NHTSA) issued the very first regulation applicable to the use of car bumpers in the country in 1971. It was called Exterior Protection, which was part of the Federal Motor Vehicle Safety Standard No. 215.

The United States Congress signed the Motor Vehicle Information and Cost Saving Act (MVICS) in October 1972. Under this rule, the NHTSA was required to release a standard for bumpers that would reduce the cost of consumers. Amongst the factors that were considered include the savings in consumer time, implementation of benefits and costs as well as the effect of the standard on legal fees and costs.

In March 1976, the requirements of the Federal Motor Vehicle Safety Standard No. 215 were merged with the important requirements of MVICS. The new and improved standard was included in the United States Code of Federal Regulations. In May 1982, the NHTSA implemented the amendments to the bumper standard.

The bumper standards in Canada and the United States were implemented at the same time. Their regulations were very much similar. The automobile industry in North America called for stronger Canadian-specification bumpers. The regulations of Canada were changed in the early parts of 2009 in accordance with the international ECE regulations as well as the federal standards of the United States.

In order to comply with the standards for bumpers in the 1970s and the early parts of the 1980s, car bumpers were made heavy, massive and bulky. By the closing parts of the 1980s, a painted thermoplastic fascia was used to conceal bumpers.

A marketing club organized by Harley-Davidson, the Harley Owner Group aims to promote the Harley-Davidson motorcycles. The organization of the club contributed to the improved financial performance of the company in the 1980s and 1990s. The members of the club receive discounts when they buy the motorcycles. The club was organized in 1983 to develop strong and long lasting relationships with the enterprise’s customers as well as employees. Whenever the organization hosts special events, members receive souvenir items like clothing. To know the size of the group, it is best to look at the number of members of the organization.

The Members of the Organization

How big is the Harley Owner Group? The size of the organization can be measured in terms of the number of the members of the club. The total membership of the organization in 1985 is 60,000. Membership in the organization improved in 1991 to 151,600. After eight years, the membership of the club increased to half million. In the early 2000s, the club’s total membership reached a million.

Another way of measuring the size of Harley Owner Group is by determining the number of the chapters of the club. In 1985, the organization has 49 chapters. Six years after, the number of chapters increased and reached 685. In 1999, the total number of chapters was 1,157.

Additional Information and Other Important Details

Harley Owner Group offers consumers and employees three types of membership, namely the full membership, the associate membership and the life membership. Those who like to apply for full membership, they should prepare $45 dollars for the membership for a year, $85 for two years and $120 for three years. On the other hand, associate membership costs $25 for a year. Members who want to renew this type of membership should allot $45 for two years and $65 for three years.

Harley Owner Group full members are entitled to all the club’s benefits. Such type of membership is only open to those who own Buell as well as Harley-Davidson motorcycles. The benefits of associate members include the membership card, the bronze HOG pin as well as the embroidered HOG patch. In addition, they can participate in the ABCs of Touring competition and the Mileage Program. Moreover, associate members can join the Safe Riders Skills Program. The full and associate members of Harley Owner Group are also members of the Ladies of Harley organization. Above all, the members of the group are welcome to join in the special events organized by Harley Owner Group.

This information is about the Enertrols shock breakers. These do not necessarily match the figures of other companies. Also keep in mind that there are many types of shock breakers and absorbers, each with their own characteristics.

Basic Factors

When figuring out shock breaker sizes, you must assess how much energy is dispersed for each cycle. The second is the amount of energy dispelled in a 60 minute operation. The application’s effective weight must be assessed also.

Kinetic Energy

The formula for determining the kinetic energy for every cycle is KE=½MV2. Remember that a moving object will be composed of inertia or inertia plus a driving force.

Effective Weight

The effective weight is crucial for getting the shock breaker correct. The general rule is this: if the impact velocities are under 1 ft/sec, choose the next highest bore size.

This is also the rule if the propelling / driving force (F x S) is beyond ½ of the E3 value (where E3 is the total energy per cycle). If you’re not sure of the shock breaker size, you must consult the shock breaker / absorber manufacturer for more information.

High and Low Effective Weight

High effective weight produces high set downforce towards the shock breaker stroke. The low effective weights generate the impact forces at the start of the stroke.

Energy Capacity of Full Threaded Body Shock Absorbers

The specs for adjustable full threaded models are the following. For model SA they are: bore: ¼ inches; stroke: ½ inches; max in/lbs cycle: 150; effective weight lbs /min/max: 5-400 lbs / 2.3-182 Kg; max in / lbs / hour 400,000 lbs; max strength: 750 lbs.

The shock breaker size and specs for model SALD are as follows: bore: 3/8 in; stroke: 1 in; maximum inch/lbs/cycle: 600 in.-lbs; effective weight lbs. min/max: 10-1,200 lbs; maximum inch-lbs/hour: 600,000 lbs; mounting strength: 1,500 lbs.

Non Adjustable Full Body Types

For the SNALD UNF Series 25 the stroke is ¼ inches; effective weight lbs: 4-12; the maximum energy capacity is 25 lbs per cycle / 750 lbs per hour. The 75 series specs are: stroke: 3/8 in; effective weight lbs: 2-36; maximum energy capacity: 75 lbs per cycle / 250,000 lbs per hour.

The specifications for the 150 are: stroke: ½ inches; effective weight lbs: 2-22; maximum energy capacity: 150 lbs per cycle / 300,000 lbs per hour.

Other Shock Breaker Sizes and Specifications

For the SNALD UNF Series 225, the stroke is ½ in; effective weight lbs: 5-55; maximum energy capacity: 225 lbs per cycle / 400,000 lbs per hour. For the 450 series, the stroke is 1 inch; effective weight lbs: 5-35; maximum energy capacity: 450 lbs per cycle / 600,000 lbs per hour.

The specs for the 600H2 are the following: stroke: 1 inch; effective weight lbs: 880-5000; maximum energy capacity: 600 lbs per cycle / 600,000 lbs per hour. These are just some of the Enertrol models; there are many more with different specifications.

Shock breaker sizes often require complex calculations to figure the one you need. Choosing the wrong one can lead to greater risks, so consulting a professional may be necessary.

Police officers and traffic enforcers commonly wear a reflective vest so that people can easily see them at night and during bad weather. The vest varies in styles and colors. Some of the most popular colors of the garment are neon yellow, neon orange and neon green. Those who work in construction and industrial sites also wear this garment for protection and safety. Most manufacturers produce the same size and dimensions of the vest. This article highlights the most common reflective vest dimensions available in the commercial market today.

The Dimensions of Reflective Vests

What are the reflective vest dimensions? The width of the garment measures 17 inches while the height measures 23 inches. The vest has vertical vinyl strips that run from back to front measures an inch. The seam binding of the vest that can be seen on the edges of the garment measures ¼ inch. The closure on the front measures 1.5 inches x 2 inches. The front flaps of the vest have a length of an inch and a width of 8 inches.

Additional Information and Other Important Details

Most reflective vests are made from polyester. Instead of hook and loop, other manufacturers of the vest use zipper or reflective tape. Some manufacturers allow customers to customize the vest. They can print texts on the garment. Aside from screen printing, manufacturers also offer woven label stitching and heat transfer printing.

There are several reasons why people use this type of vest. The main reason for using this vest is to allow the wearer to be more visible. This type of vest is categorized into three. The first category includes vests that offer minimal amount of reflective as well as bright material. The second and third categories are the highly visible vests, which use high amount of bright material.

Some of the benefits that people get from this vest include minimal traffic fatalities, especially in construction areas. In some countries, the national government extends the use of the vests to media professionals. However, even if there are regulations about the professionals who should wear the vests, others also wear the garment for their safety. Some people who wear reflective vests are sports enthusiasts like cyclists as well as joggers. In some regions of the world, hunters wear the vests so that the other hunters can see them.

The usual price of the vest is around $5 to $10. However, consumers can get discounts if they will purchase the garment in bulk.

A parking space is commonly found within a parking lot or a parking garage. Of course, it can also be found along a city street as well as many other places that are designated for the primary purpose of parking vehicles. Each space is usually marked with three lines, one on the right, the other on the left and another line at the top. White paint is commonly used to mark these lines. Parking spaces may be arranged with an angle, perpendicularly or in a parallel manner. Aside from these interesting facts, it is also good to know the dimensions of a parking space.

The Different Sizes of Parking Spaces

The average size of a parking space is 320 square feet or 30 square meters. However, there are also other sizes available, one of the most common of which is 270 square feet or 25 square meters. These sizes include the landscaping or end of aisle areas, the circulation areas and the parking space. For perpendicular or angled parking spaces, the length is commonly 16 feet to 18 feet or 4.9 meters to 5.5 meters. Meanwhile, the standard width is 7.9 feet to 9 feet or 2.4 meters to 2.75 meters. Some other versions of this type of parking space measure between 7.5 feet and 10 feet or 2.3 meters and 3.2 meters.

For parallel parking spaces, the standard width is 7.9 feet or 2.4 meters while the standard length is 20 feet or 6.1 meters. They are usually marked 6.9 feet to 7.9 feet or 2.1 meters to 2.4 meters wide. Inclusive of the entry and exit maneuvering, the standard length ranges from 22 feet to 26 feet or 6.7 meters to 7.9 meters.

Additional Facts and Other Interesting Details

In the United States, details about curb markings are specified in the Manual of Uniform Traffic Control Devices. Some local highway agencies use special colors for such purposes. The main reason behind this is to supplement the standard signs for the overall improvement of parking regulation.

The state of California uses different kinds of colors for this particular purpose. For passenger drop off or pickup, the usual color is white. For parking spaces that are limited by time, the designated color is green. For loading, the assigned color is yellow. For disabled individuals using proper vehicle identification, the appropriate color is blue. For emergency vehicles, the red curb means no parking, no standing and no stopping. To indicate a no parking zone, the curb is commonly marked yellow.

The Jeep Wrangler is a sports utility vehicle manufactured by Chrysler. Although the specifications of the models vary, they all utilize live axles.

Dimensions of a Jeep Wrangler: the YJ (1987-2005)

The Jeep YJ 1987-89 models are 152.6 in (3876 mm) long, while the 1990-92 versions are 153 in (3886 mm) long. The 1993-95 models are 151.9 in (3860 mm) long. The width is 66 in (1676 mm). The height is 71.9 in (1825 mm) for the 1993-95 models.

For the 1993-95 Soft Top, the height is 72 in (1827 mm) while for the 1987–1992 Hardtop it is 69.6 in (1769 mm). The fuel capacity is 15 U.S. gal. Some models have a higher capacity at 20 U.S. gal. The wheelbase is 93.4 in (2373 mm) for all the models.

Dimensions of a Jeep Wrangler: the TJ (1997-2006)

The wheelbase is 93.4 in (2,370 mm (standard) or 103.4 in (2,630 mm) LWB. The length of the 1997-99 models is 151.2 in (3841 mm). For the 2000-03 models it is 155.4 in (3947 mm); for the 2004-06 SWB it is 154.9 in (3934 mm), while the 2004-06 LWB is 171 in (4343 mm) long.

The width for the 1997–2003, 2004-06 LWB is 68.3 in (1735 mm); for the 2004-06 SWB it is 66.7 in (1694 mm). The height is 70.2 in (1784 mm) for the 1997-99 models, 71.1 in (1805 mm) for the 2000-01 versions and 70.9 in (1800 mm) for the 2002-03 & 2004-06 LWB. For the 2004-06 SWB models it is 71.2 in (1808 mm).

The dimensions of a Jeep Wrangler in the TJ class give it a fuel capacity of 15 U.S. gal (57 L; 12 imp gal). Others have a capacity of 19 U.S. gal (72 L; 16 imp gal). The jeep is a 2 door convertible. The engines used are 2.5 L AMC 150, 2.4 L PowerTech I4 and 4.0 L AMC 242 I6.

The transmissions are 3-speed automatic, 6-speed manual, 5-speed Aisin AX-15 manual and 4-speed automatic. A right hand version of the vehicle became available for export to other countries. The TJ Wrangler Rubicon came out in 2003.

Dimensions of a Jeep Wrangler: JK (2007-Present)

The wheelbase is 95.4 in (2423 mm) for the 2-door and 116 in (2945 mm) for the 4-door. The length is 152.8 in (3880 mm) for the 2-door and 173.4 in (4405 mm) for the 4-door. The width is 73.7 in (1872 mm) for the 2-door and 73.9 in (1877 mm) for the 4-door.

The height is 70.9 in (1800 mm). For the 2-door Rubicon it is 72.3 in (1836 mm). The fuel capacity is 21.6 U.S. gal (82 L; 18.0 imp gal). The engine is 3.8 L EGH V6 and the transmissions are 4-speed automatic and 6-speed manual. All the JK models have the anti-lock braking system installed.

The dimensions of a Jeep Wrangler are always being evaluated by the manufacturer. The specifications of future SUV models are based on what will bring optimum safety and performance.

A crankshaft is the engine component that sets reciprocating linear piston motion to rotation. In most cases the crankshaft is linked to a flywheel.

Crankshaft Dimensions: Ford 302

The specifications for the K1 Technologies Ford Windsor V8 5.0 L 302 crankshafts are as follows. The .030 oversize bore is 332 cubic inches (for the 3.250 stroker crank). Using the 3.400 stroker crank, the oversized bore is 347 cubic inches.

It has the 6 bolt Ford rear flange and has straight oil holes. Other features include a hardened core and stock 302 5.0 Ford (main journal size). The cranks are best used on the 302 Ford Mustang.

They can also be used on a dragster, hot rod turbo and racing engines. The cranks are also for nostalgia dragsters, supercharged engines and street cars.

Crankshaft Dimensions: Dodge 340 Crank

The 3.790 stroke crank has a 030 bore measuring 394 cubic inches. The 4.000 stroke crank has a 030 bore measuring 416 cubic inches. The cranks are forged steel, nitrided and core hardened.

They have straight oil holes. Other features include 340 main journal (size is 2.500 in), 6 bolt Chrysler rear flange and is Mag-Particle inspected. These cranks are best used with the K1 4340 Billet H beam 340 rods.

There are three stroke types: the 3.790 (340 Chrysler 4340 Forged Stroker Crank 3.790 Stroke 2.100 rod journal), 4.000 (SB Chrysler 340 4340 Forged Stroker Crank 4.000 Stroke 2.100 rod journal) and 4.000 (SB Chrysler 340 4340 Forged Stroker Crank 4.000 Stroke 2.125 rod journal).

Crankshaft Dimensions: K1 426 Hemi Engine 4340

The stock stroke is 3.750 in. The main journal size is 2.750 in, while the rod pin is 2.375 in. The crankshaft is constructed from 4340 grade steel. The crankshafts utilize 125" fillet radii to increase its strength.

The crankshafts can be used to reconstruct a hot rod, dragster, drag race 426 hemi and other projects. Another feature is the 8 bolt flange. The rod pin sizes also differ according to the crank.

For the K1 Tech. 4340 forged steel 3.750" stock 426 Hemi crank stroke, the rod pin is 2.375, while for the K1 Tech. 4340 forged steel 4.250" it is 2.200.

Crankshaft Dimensions: Small Block Mopar Eagle Cranks

The Eagle crankshaft is intended for use on Mopar small block engines. The stock is 3.310 inches for the 273 318 340 5.2 Magnum. For the 360 5.9 Magnum the stock stroke is 3.580 inches (note: the cast steel crank is for below 500 hp engines only).

For the 103403310, the stroke is 3.310" and the bobweight is 2050. For the 103404000 the stroke is 4.000" and for the 434033106123 it is 3.310". For the 434040006123 the stroke is 4.000". For the 103603580 it is 3.580" and for the 436035806123 it is 3.580". The bobweight is 2050 for all these parts. The cranks are either forged steel or cast iron.

The crankshaft dimensions and specs may be different for your building project. The type needed will depend on the vehicle you are using or trying to construct.

The piston’s purpose is to relay the force from the gas to the crankshaft. The following are some of the more important specs in piston kits sold today.

Piston Engine Dimensions: Ross Racing Small Block Chevy Piston

Part 99450’s bore is 4.003 and the stroke is 3.480. The rod length is 5.700 and the dome height is -.090 and it is 428 grams. Part 92450 has a 4.020 bore, 3.480 stroke with a rod length of 5.700. The dome height is also -.090 and is 445 grams.

Part 90450 has a 4.030 bore, 3.480 stroke and a 5.700 rod length. The dome height is -.090 and is 456 grams. The 99527 has a 3.750 bore, 3.750 stroke and 5.700 rod. The bore height is -.120 and it is 500 grams. The 94450 has a 4.035 bore, 4.035 stroke and 5.700 rod. The dome height is -.090 and is 459 grams.

Piston Engine Dimensions: Ross HD Flat Top 22

Part 94455 has a 4.020, 3.480 stroke and 5.700 rod length and is 505 grams. Part 90455 also has 4.030 bore, 3.480 stroke and 5.700 long rod. It is 514 grams. Part 90465’s bore is 4.030 and the stroke is 3.480. The rod length is 6.000 and it is 469 grams.

Part 90455 has a 4.030 bore, 3.750 stroke and 5.565 rod length. It is 514 grams. Part 90755 has a 4.030 bore, 3.750 stroke and 5.700 rod length. It is 490 grams. The 90765 has 4.030 bore, 3.750 stroke and 6.000 rod length and is 486 grams. Part 92455 has a 4.035 bore, 3.480 stroke and 5.700 rod length. It is 509 grams.

Piston Engine Dimensions: ROSS Ludicrous Liteness

Part 99456 has a 4.003 bore, 3.480 stroke and rod length of 5.700. It is 399 grams. Part 99166 has a 4.003 bore, 3.480 stroke, rod length of 6.000 and 362 grams. Part 92456 has a 4.020 bore, 3.480 stroke, 5.700 rod length and 419 grams. As for part 92466, it has a 4.020 bore, 3.480 stroke, 6.000 rod length and is 376 grams.

The 90002 has a 4.030 bore, 3.480 stroke and 5.700 rod length. It is 433 grams. Part 90456 has a 4.030 bore, 3.480 stroke and 5.700 rod length; it is 428 grams. Part 90926 has a 90926 bore, 3.480 stroke, 5.700 rod and is 440 grams.

Piston Engine Dimensions: CP Bullet Flat Top SBC

Part BC 1020-STD has a 4.000 bore, 3.500 stroke and 6.000 rod. Part BC 1020-020 has a 4.020 bore, 3.500 stroke and 6.000 rod. The BC 1020-030 has a 4.030 bore, 3.500 stroke and 6.000 rod. The specs for the BC 1020-040 are 4.040 (bore), 3.500 (stroke and 6.000 (rod).

The BC 1020-060 has a 4.060 bore, 3.500 stroke and 6.000 rod. Part BC 1021-STD has a 4.000 bore, 3.480 stroke and 5.700 rod. The bore for BC 1021-020 is 4.020 and the stroke is 3.480. The rod is 5.700.

The piston engine dimensions set down here are only examples of what you will come across. Manufacturers use different specs for their piston engines.